WATERPROOFING

An area within a building supplied with a waste, and the advantage of the

systems are to prevent moisture entering the substrate or adjacent areas and graded to

wastes to dispose of water without ponding .

A lack of

maintenance leads to:

1. Unnecessary and often extensive repairs

2. The costly replacement of

3. The deterioration of properties

4. Possible structural damage

5. The frustration the “nuisance” value

6. Damage to internal property (valued paintings, carpets, wooden etc.)

7. Insurance companies unwilling to cover claims (as said to be preventative maintenance)

Recommended used materials:

• Cementitious Coating

• Acrylic Coating

• Polyurethane Liquid Coating

• Liquid Membrane Coating

TECHNOECO C EMEN TITIO US &

FIBRATED WATERPROOFING

Cementations systems generally are available as ready to apply.

The two components systems consist of a resin base which is

normally an acrylic co-polymer with water proofing properties and

a cementations powered roller or by spray . A fabric scrim we

suggested over expansion joints to protect the layer from tensile

thermal expansion on the roof. Cementations systems are also

applied over spray applied polyurethane thermal insulation as a

protective layer, as these systems possess high resistance to UV

rays. Since application skills require are minimum, they highly

popular among maintenance contractors. However, it should be

noted that the waterproofing and durability membrane and care

should be exercised in choosing one with adequate co-polymer

content.

TECHNOECO WATER TANKS

& SWIMMING POOLS

When constructing a new water tank or swimming pool, it is possible to apply the

system to the internal (negative) or external (positive) side of the wall.

In many cases, combined systems are to provide enhanced protection.

Our clients can avail from us water tanks & swimming pools

services.

These services help in enhancing the life of the water tanks/swimming pools by

avoiding water from damaging the walls. Our skilled workers perform two chemical

coat systems with mesh on the tanks/swimming pools. The coating done is

highly insoluble in the water. These services are accomplished in less time period

and come with a warranty of five years.

Recommended used materials:-

Cementitious Coating

Crystalline

Epoxy Coating

TECHNOECO INDUSTRIAL

FLOOR COATING

Car Park Epoxy coating I - Heavy duty Polyurethane coating I - Slip Resistance coating

Expansion Joints I -Sealant.

Epoxies are polymer materials that begin life as liquids and are converted to the solid

polymers by a chemical reaction. An epoxy based polymer is mechanically strong,

chemically resistant to degradation of the chemical elements in the solid form and

highly adhesive during conversion from liquid to solid . There are a wide range of basic

epoxy chemicals from which an epoxy system can be formulated .

Epoxy coating is used indoors where a hard , very durable paint surface is needed. It’s

commonly used, therefore, for (and/or walls) in garages (both commercial and

res idential), factories , shops and other

areas.

There are, however, several types of epoxy/ Polyurethane coating to

choos e from:

Epoxy Solvent Free coating

Epoxy Solvent base coating

Polyurethane UV Resistant Heavy Duty Coating

TECHNOECO THERMAL

INSULATION SERVICE

The accelerated constructional activities couple d with the ever increasing demand for

economical and comfortable living encourages us to adopt the latest and

technology advancements. Hence we have chosen the concept of the Thermal Insulation

System, which plays a vital role in improving the cooling conditions inside buildings. This

on power consumption and money involved for all parties concerned

in the construction process.

Thermal Insulation System has been introduce d to reduce your electric consumption

costs up to 40%, thus saving money and the country’s energy resources. It also indeed

creates a more comfortable living and working atmosphere.

TECHNOECO INJECTION

TREATMENT

SECTION I: GENERAL INSTRUCTIONS

• All materials whether loose or on pallets have to be stored in a covered area and protected from

UV and sunlight. Damage to the material may be caused due to improper storage and at high

temperatures.

• Application of materials should be avoided in case of extreme weather conditions like sand

storm or rain. The ambient temperature during application should be between 5°C and 45°C.

SECTION II: APPLICATION INSTURCTIONS

SURFACE REQUIREMENTS

Drill the hole adjacent to the crack in 45° angle & adjacent to the pipe penetration.

In the presence of running water the must be stopped using POLYINJECT STOP or

POLYINJECT STOP FS which produces rapid setting water-stopping foam. When the water is

stopped the cracks are re-injected with POLYINJECT PU+.

WORK PREPARATIONS

POLYINJECT PU+ is applied as injection resin with using injection packers and 1-C pumps. The

injection packers may be into holes drilled directly into the crack or drilled diagonally from

concrete adjacent to the crack or by of injection nipples bonded to the surface using

POLYPUR F on damp surfaces or POLYPOXY BF on dry surfaces. For further assistance and

instructions regarding the packer and design please refer to our method statement.

MIXING

Pour the hardener (component B) into the resin (component A) in the indicated mixing ratio and

mix with an electrical mixer (max. 300 rpm) until a homogenous mixture is produced. Assure

that the B component is evenly dispersed. Only mix resin that can be used within the

pot life of the material.

TECHNOECO INJECTION

TREATMENT

INJECTION

• POLYINJECT PU+ can be injected with using 1-component or 2-component injection pumps.

The injection pressure should be at least 4 bars. After the work is the injection system

shall be allowed to cure for 24 hours and shall be left undisturbed for this time.

CLEANING

• Remove the packers once POLYINJECT PU+ is fully cured and make good any holes or voids

with POLYPOXY BF on dry surfaces and allow curing. In case of damp surfaces use POLYPUR

F. POLYINJECT PU+, POLYPOXY BF and POLYPUR F should be removed from tools, equipment

and mixers with an appropriate solvent immediately after use. Hardened material can only be

removed mechanically.

SECTION III: STORAGE & SHELF LIFE

• Store all material between 10 and 25°C in a cool, covered dry place. Do not expose the

containers to direct sunlight and keep away from all sources of heat. In tropical climatic

conditions, the product has to be stored in an air-conditioned environment and protected from

high humidity. The shelf life of the product is 6 months in unopened condition if stored as per

the recommendations. Exposure to high temperature and humidity will result in considerable

deterioration of the product and reduce its shelf life.

Note: As with all construction chemical products caution should be always be exercised whilst

usage. Protective clothing such as gloves and goggles should be worn. Treat any splashes to the

skin or eyes with fresh water immediately and seek medical advice. Should any of the product

be accidentally swallowed do not induce vomiting, but call for medical assistance immediately.

Ensure that the container is available for medical attendant to examine any relevant instructions

and contents details. For any further information please refer to the material safety datasheet.

TECHNOECO GENERAL

MAINTENANCE

Supreme Water and Insulation is specialized water contractors having

the honor of your attention to take this opportunity and introduce that we are specialized r

 contractor for water p System by you a quick overview of our

professional past, committed and dedicated present for achieving prosperous future for

us and to our valued clients.

TECHNOECO PAINTING SERVICE

Interior ceiling and wall painting is a project that’s best divided into two: cutting in and

rolling.(Having two people do the work is nice —especially if you’re not one of them) one

person uses a brush to cut in, or outline, all the areas that a paint roller can’t cover without

getting paint on an adjacent surface. The other member of the team spreads paint on the

ceiling and walls with a roller. If the ceiling and walls are the same color, you can cut in

both at the same time. Otherwise, work on the ceiling

If you’re painting with a partner, have the person with the brush start by spreading a

2-inch band of paint on the ceiling, all around its perimeter. Lap marks result if the cut-in

paint dries before you blend in the rolled area with the cut-in area, so don’t let the outliner

get too far ahead of the roller. You also want the roller to roll over as much of the cut-in

band of paint as possible. The textures that a brush and a roller leave are quite